Triner-scale RAVAS-310 Instrukcja Użytkownika

1 RAVAS-310 OWNERS MANUAL

10 THE TOUCH PANEL Each key has 2 operational and one entry function Key Function level 1 (short key press) Function level 2 (long key press) Funct

11 ERROR MESSAGES Displayed error Meaning Out of error mode Err01 Load cell signal is unstable Automatic Err02 Overload on full scale Automatic aft

12 3.3 INDICATOR FUNCTIONS GRADUATION From 0 to 5000 lbs the weight is shown in 2 lb increments. BEFORE WEIGHING: CHECK ZERO POINT Before each

13  Press the PT key until the display changes and the last digit is blinking (approx 3 seconds).  The display shows the current tare value. 

14 Or  Change the piece weight value by using the  or  and  keys.  The display shows the new piece weight.  To accept the new value press EN

15 3.4 PRINTER (Option) The RAVAS 310 comes equipped with a thermal printer. Obtained and entered weighing data can be printed. THE PRINT OUT

16 CHANGING THE THERMAL PAPER ROLL Open the printer cover by pressing down the 2 levers and pulling the cover towards you. Remove the existing

17 CHANGING THE TIME AND DATE ON THE PRINT-OUT The date and time can be printed together with the weight information.  Press the key for 6 sec

18 4 TROUBLE SHOOTING No power Change batteries Replace battery pack Use a fully charged battery pack. (see page 5) 12Vdc on the board Check the bo

19 The potentiometers with which we calibrate the output of the load cells, are mechanical parts therefore, higher risk components Move the board an

2 OPERATORS MANUAL RAVAS-310 INDEX PAGE 1. Safety Instructions 3 2. System Setup 4 3. Operation Manual 6 3.1 Using the Weigh

20 Not summing Operator error . Load is not stable. Scale needs to be unloaded before accepting new print. System will not print weights that are sm

21 5 SPARE PARTS

22 SPARE PARTS LIST Weighing Hand Pallet Truck RAVAS 310 Nr Article Number Description Quantity 1 899193001.3 set fork shoes 1 2 895200708 chassis 1

23 6 CALIBRATION CALIBRATION INSTRUCTIONS INDICATOR 310 The calibration mode can only be reached from the standard weighing mode. You cannot get i

24 MULTI-POINT CALIBRATION  Push the T key for about 10 seconds.  After 3 seconds the display will show the last entered pre-set tare value. 

25 7 PARAMETER SETTINGS ATTENTION: Before entering the setup mode make sure that the battery supply is sufficient. A low battery may cause the mi

26 PARAMETERS: Parameter Function Settings Default US 01 Start-up unit (and print units) 1=kg / 2=lb 2 02 Smallest graduation step for multi-range 0

27 25 Dataprotocol comport 1 0-4 0 0=PC bi-directional command structure 1=not used 2=Remote display continuously 3=Printer (wi

28 91 Reset to default parameter If parameter 01 was on 1 it will default to the settings including calibration EU settings. If P_01 =2 the US

3 1 SAFETY INSTRUCTIONS 1. NEVER lift a heavy load with just the points of the forks. This could damage the electronic weighing elements permanen

4 2 SYSTEM SETUP MOUNTING THE PUMP HANDLE Make sure the lever is pushed down to the “pump” position. Thread the chain through the hole in the

5 THE BATTERY The power supply to the system takes place through an exchangeable battery pack. A completely charged battery should operate for a tot

6 3 OPERATION MANUAL INDEX PAGE 3.1 Using the Weighing Hand P

7 3.1 USING THE WEIGHING HAND PALLET TRUCK Accurate Weighing The weight must be centered over the forks of the pallet truck and lift freely: with

8 TAKING THE SYSTEM INTO OPERATION To activate the scale turn it on using the on/off () button on the terminal. After 3 to 5 minutes the electroni

9 3.2 TOUCH PANEL INDICATOR Indicator Front There are 3 display-modes: lbs, kg or the number of pieces. Also the battery sign is integrated in